References

Chang, K.H., Y.C. Chang and I.T. Tsai, 2013. Enhancing FMEA assessment by integrating grey relational analysis and the decision making trial and evaluation laboratory approach. Eng. Fail. Anal., 31: 211-224.
Direct Link  |  

Chen, Z., Y. Huang, H. Huang, Z. Zhang and G. Zhang, 2015. Three-dimensional characteristics analysis of the wire-tool vibration considering spatial temperature field and electromagnetic field in WEDM. Int. J. Mach. Manuf., 92: 85-96.
Direct Link  |  

Deris, A.M., A.M. Zain and R. Sallehuddin, 2013. Hybrid GR-SVM for prediction of surface roughness in abrasive water jet machining. Meccanica, 48: 1937-1945.
CrossRef  |  Direct Link  |  

Dixit, A.C., A. Kumar, R.K. Singh and R. Bajpai, 2015. An experimental study of material removal rate and electrode wear rate of high carbon-high chromium steel (AISI D3). Int. J. Innovative Res. Adv. Eng., 2: 257-262.
Direct Link  |  

Khan, M.A.R., M.M. Rahman and K. Kadirgama, 2014. Electrode wear rate of graphite electrodes during electrical discharge machining processes on titanium alloy Ti-5Al-2.5 Sn. Int. J. Automot. Mech. Eng., 9: 1782-1792.
Direct Link  |  

Li, L., Z.Y. Li, X.T. Wei and X. Cheng, 2014. Machining characteristic of Inconel 718 by die sinking-EDM and wire-EDM. Mater. Manuf. Processes, 30: 968-973.

Pandey, S.N. and S. Alam, 2015. An experimental investigation of Electrode Wear Rate (EWR) on EDM of SS-202 using different electrodes. Int. J. Eng. Res. Technol., 4: 2341-2347.
Direct Link  |  

Pandey, S.N., S. Alam and M.A. Siddiqui, 2014. Effect of electrode wear rate on machining of stainless steel-202 using copper electrode in edm. Carbon, 100: 1-15.

Pramanik, A., 2004. Developments in the non-traditional machining of particle reinforced metal matrix composites. Int. J. Mach. Tools Manuf., 86: 44-61.
Direct Link  |  

Sallehuddin, R., S.M. Shamsuddin and S.Z.M. Hashim, 2010. Forecasting small data set using hybrid cooperative feature selection. Proceeding of the 12th International Conference on Computer Modelling and Simulation, March 24-26, 2010, IEEE, Skudai, Malaysia, ISBN:978-1-4244-6615-3, pp: 80-85.

Sarıkaya, M. and A. Gullu, 2015. Multi-response optimization of minimum quantity lubrication parameters using taguchi-based grey relational analysis in turning of difficult-to-cut alloy haynes 25. J. Cleaner Prod., 91: 347-357.
Direct Link  |  

Selvakumar, S., K.P. Arulshri, K.P. Padmanaban and K.S.K. Sasikumar, 2013. Design and optimization of machining fixture layout using ANN and DOE. Int. J. Adv. Manuf. Technol., 65: 1573-1586.
CrossRef  |  Direct Link  |  

Shabgard, M.R. and H. Alenabi, 2015. Ultrasonic assisted electrical discharge machining of Ti-6Al-4V Alloy. Mater. Manuf. Processes, 30: 991-1000.
Direct Link  |  

Sulaiman, S., M.S. Sany and M.S. Said, 2015. Analysis of surface roughness and material removal rate for metal matrix composite AlSi/10% ALN in EDM Die sinking operation. Manuf. Sci. Technol., 3: 300-307.
Direct Link  |  

Takezawa, H., N. Yokote and N. Mohri, 2016. Influence of external magnetic field on permanent magnet by EDM. Int. J. Adv. Manuf. Technol., 87: 25-30.
CrossRef  |  Direct Link  |  

Tang, L. and Y.F. Guo, 2014. Electrical discharge precision machining parameters optimization investigation on S-03 special stainless steel. Int. J. Adv. Manuf. Technol., 70: 1369-1376.
CrossRef  |  Direct Link  |  

Tiwary, A.P., B.B. Pradhan and B. Bhattacharyya, 2015. Study on the influence of micro-EDM process parameters during machining of Ti-6Al-4V superalloy. Int. J. Adv. Manuf. Technol., 76: 151-160.
CrossRef  |  Direct Link  |  

Yadav, H.C., R. Jain, A.R. Singh and P.K. Mishra, 2016. Kano integrated robust design approach for aesthetical product design: a case study of a car profile. J. Intell. Manuf., 2016: 1-19.
Direct Link  |  

Yu, J.W., L.H. He, X.M. Sheng, W. Duan and S.H. Yin et al., 2014. Experimental investigation of copper-tungsten electrode wear in EDM. Adv. Mater. Res., 1017: 818-824.
Direct Link  |  

Zhang, Y., Z. Xu, D. Zhu, N. Qu and Y. Zhu, 2016. Drilling of film cooling holes by a EDM-ECM in situ combined process using internal and side flushing of tubular electrode. Int. J. Adv. Manuf. Technol., 83: 505-517.
CrossRef  |  Direct Link  |