References

Baskakov, A.P., B.V. Berg, O.K. Vitt, Kuznetsov and V. Yu. et al., 2010. Heat Engineering: Text Book for Higher Educational Institutions. Bastet Publisher, Moscow, Russia, Pages: 328.

Deng, Y., H. Liu, X. Zhao, E. Jiaqiang and J. Chen, 2018. Effects of cold start control strategy on cold start performance of the diesel engine based on a comprehensive preheat diesel engine model. Appl. Energy, 210: 279-287.
CrossRef  |  Direct Link  |  

Gabdrafikov, F.Z., M.A. Abrarov, I.A. Abrarov and U.S. Galiakberov, 2016. [Pre-start heating device for an internal combustion engine]. MPK Company, Moscow, Russia. (In Russian)

Gabgrafikov, F.Z. and F.A. Sharifullin, 2012. [Fuel pump of higher injection rate (In Russian)]. Mach. Agric., 3: 25-26.

Gabgrafikov, F.Z., 2016. [Basics of Heat Engineering]. Bashkir State Agrarian University, Ufa, Russia, Pages: 160 (In Russian).

Gabgrafikov, F.Z., U.S. Galiakberov and V.M. Gindullin, 2017. [Energy-saving system for pre-start engine eheating (In Russian)]. Rural Mech., 5: 30-31.

Gabgrafikov, F.Z., U.S. Galiakberov and V.M. Gindullin, 2017. [Energy-saving system for pre-start engine heating in car and tractor machinery (In Russian)]. Eng. Econ., 11: 82-91.

Kalinin, V.F., A.M. Shuvalov and S.V. Kochergin, 2002. [Mathematical model of motor oil heating process in internal combustion engines with self-regulated heaters (In Russian)]. Bull. Tambov State Tech. Univ., 8: 628-632.

Kartoshkin, A.P., 2012. [Technological Liquids for Car and Tractor Machinery]. Akademia, Moscow, Russia, Pages: 236 (In Russian).

Kumar, A., S.K. Shukla and J.V. Tierkey, 2016. A review of research and policy on using different biodiesel oils as fuel for CI engine. Energy Procedia, 90: 292-304.
Direct Link  |  

Petrichenko, R.M., 1985. [Liguid Cooling System for High-Speed Internal Combustion Engines]. Mashinostroenie, Leningrad, Russia, Pages: 224 (In Russian).

Prabu, S.S., M.A. Asokan, S. Prathiba, S. Ahmed and G. Puthean, 2018. Effect of additives on performance, combustion and emission behavior of preheated palm oil/diesel blends in DI diesel engine. Renewable Energy, 122: 196-205.
CrossRef  |  Direct Link  |  

Rath, M.K., S.K. Acharya and P.P. Patnaik, 2017. CI engine performance during cold weather condition using preheated air and engine by waste energy. Intl. J. Ambient Energy, 38: 534-540.
Direct Link  |  

Royo, R., M.A. Albertos-Arranz, J.A. Carcel-Cubas and J. Paya, 2012. Thermographic study of the preheating plugs in diesel engines. Appl. Therm. Eng., 37: 412-419.
CrossRef  |  Direct Link  |  

Song, J., X.S. Li, X.D. Ren and C.W. Gu, 2018. Performance improvement of a preheating supercritical CO₂(S-CO₂) cycle based system for engine waste heat recovery. Energy Convers. Manage., 161: 225-233.
CrossRef  |  Direct Link  |  

Thakar, R., S. Bhosle and S. Lahane, 2018. Design of heat exchanger for waste heat recovery from exhaust gas of diesel engine. Procedia Manuf., 20: 372-376.
Direct Link  |  

Vajja, S.R. and R.B.V. Murali, 2016. Performance evaluation of diesel engine with preheated bio diesel with additives. IOP. Conf. Ser. Mater. Sci. Eng., 149: 1-10.
CrossRef  |  Direct Link  |  

Yilmaz, N., 2012. Effects of intake air preheat and fuel blend ratio on a diesel engine operating on biodiesel-methanol blends. Fuel, 94: 444-447.
CrossRef  |  Direct Link  |  

Zhou, T., C. Yao, Y. Hu, F. Yang and J. Wang et al., 2016. Research on performance and temperature control of glow plugs for PPCI low load assist. IFAC. Pap. Online, 49: 223-230.
CrossRef  |  Direct Link  |